EXPERIMENTAL STUDY ON MOLD HEATING TEMPERATURE AND TIME VARIATIONS IN LOST WAX CASTING OF PROPELLER FOR UNMANNED SURFACE VEHICLE

Authors

  • Gusti M Mufid Daffa Akhdaan Universitas 17 Agustus 1945 Surabaya
  • Eka Widian Maulana Saputra Universitas 17 Agustus 1945 Surabaya
  • Moh Nor Ali Aziz Universitas 17 Agustus 1945 Surabaya

DOI:

https://doi.org/10.26740/otopro.v22n1.p1-8

Keywords:

Lost Wax Casting, Mold Heating Temperature, Holding Time, Aluminum 6061, Propeller Casting

Abstract

The increasing demand for high-performance propulsion systems in unmanned surface vehicles (USVs) requires propellers with high dimensional accuracy, minimal defects, and superior surface quality. Lost wax casting enables the production of complex propeller geometries; however, casting quality is strongly influenced by mold heating parameters during the burnout stage. This study investigates the effect of mold heating temperature and holding time on surface defects, density, and dimensional shrinkage of Aluminum 6061 propellers produced by the lost wax casting process. An experimental method was applied using three mold heating temperatures (660°C, 710°C, and 760°C) and three holding time variations (60–70 minutes, 120–130 minutes, and 180–190 minutes). Surface quality was evaluated through dye penetrant testing, internal integrity was assessed using density measurement based on the Archimedes principle, and dimensional accuracy was determined through shrinkage analysis. The results indicate that insufficient preheating at 660°C caused significant surface porosity, lower density, and higher shrinkage due to incomplete wax burnout. Increasing the temperature to 710°C significantly improved casting quality, with the holding time of 120–130 minutes producing minimal surface defects, relatively high density, and reduced shrinkage. Although 760°C yielded high density and low shrinkage at longer holding times, excessive thermal exposure indicated potential mold degradation. It can be concluded that a mold heating temperature of 710°C with a holding time of 120–130 minutes provides the most balanced and optimal condition for producing Aluminum 6061 propellers with improved surface integrity, internal soundness, and dimensional stability suitable for USV applications.

Author Biographies

Gusti M Mufid Daffa Akhdaan, Universitas 17 Agustus 1945 Surabaya

Fakultas Teknik Dan Program Studi Teknik Mesin

Eka Widian Maulana Saputra, Universitas 17 Agustus 1945 Surabaya

Fakultas Teknik Dan Program Studi Teknik Mesin

References

A. Nor ali, E. Santoso, and N. Martini, “Jurnal Rekayasa Mesin Moh . Nor Ali Aziz dkk / Jurnal Rekayasa Mesin,” vol. 17, no. 3, pp. 463–472, 2022.

A. Sudiyanto, “Proses Pengecoran Logam Dan Analisa Cacat Pada Produk B3x6,” Angew. Chemie Int. Ed. 6(11), 951–952., vol. 4, no. March, pp. 763–773, 2020.

T. P. Soemardi, A. Suwandi, G. Kiswanto, and W. Kusumaningsih, “The effect of temperature increase, holding time and number of layers on ceramic shells using the investment casting process,” Int. J. Technol., vol. 7, no. 6, pp. 1035–1044, 2016.

P. B. Santoso and P. Partono, “PENGARUH VARIASI PERBEDAAN POSISI PELETAKAN SALURAN MASUK (IN GATE) PADA SALURAN TURUN (DOWNSPRUE) TERHADAP PENYUSUTAN, DENSITY, KEKERASAN, DAN STRUKTUR MIKRO MENGGUNAKAN METODE INVESTMENT CASTING,” pp. 1–20, 2024.

Adri and D. Masnur, “Studi kekasaran permukaan produk investment casting aluminium minuman kaleng bekas dengan parameter temperatur tuang dan ukuran butir lempung,” J. Online Mhs., vol. 3, no. 1, pp. 1–6, 2016.

A. Dermawan and A. E. Pramono, “Engineering and Process of Investment Casting for Pump Impeller,” Recent Eng. Sci. Technol., vol. 01, no. 04, pp. 11–19, 2023.

W. K. Luk and B. W. Darvell, “Effect of burnout temperature on strength of gypsum-bonded investments,” vol. 19, pp. 552–557, 2003, doi: 10.1016/S0109-5641(02)00104-5.

S. Z. Mohd Nor, R. Ismail, S. Ahmad, and M. I. N. Isa, “The effect of dewaxing and burnout temperature in block mold process for copper alloy casting,” Int. J. Eng. Technol., vol. 7, no. 5, pp. 1905–1915, 2015.

A. K. Putera, A. Suprihanto, and Y. Umardani, “Perancangan dan Pembuatan Propeller Perahu Nelayan Dengan Metode Investment Casting Pola Lilin dan Cetakan Pasir,” JMPM (Jurnal Mater. dan Proses Manufaktur), vol. 5, no. 2, pp. 100–113, 2022, doi: 10.18196/jmpm.v5i2.11774.

Angga Setya Utama Putra, “Studi Pengecoran Aluminium Dengan Metode Gravity Die Casting Dan Gravity Investment Casting Terhadap Density, Porositas, Struktur Mikro Dan Kekerasan,” 2021.

Y. Xu, G. Li, W. Jiang, J. Zhan, Y. Yu, and Z. Fan, “Investigation on characteristic and formation mechanism of porosity defects of Al–Li alloys prepared by sand casting,” J. Mater. Res. Technol., vol. 19, pp. 4063–4075, 2022, doi: 10.1016/j.jmrt.2022.06.148.

M. Tanaka, G. Girard, R. Davis, A. Peuto, and N. Bignell, “Recommended table for the density of water between 0 °C and 40 °C based on recent experimental reports,” Metrologia, vol. 38, no. 4, p. 301, 2001, doi: 10.1088/0026-1394/38/4/3.

S. S. Herfurth K, Springer Handbooks. 2021.

M. N. A. Aziz, Rusnaldy, P. Munyensanga, S. A. Widyanto, and Paryanto, “Application of lost wax casting for manufacturing of orthopedic screw: A review,” Procedia CIRP, vol. 78, no. March, pp. 149–154, 2018, doi: 10.1016/j.procir.2018.08.304.

M. R. Kaka Zada, M. Makmur, and Rusman, “Analisis Pengujian Metode Liquid Penetran Testing Bedasarkan Acceptance Criteria Penetrant Testing Pada Komponen Cessna 152,” JAMETS J. Aircr. Maint. Eng. Aviat. Technol., vol. 2, no. 1, pp. 24–33, 2023, doi: 10.46509/jamets.v2i1.436.

S. Seifeddine and T. B. , Emma Sjölander, “On the Role of Copper and Cooling Rates on the Microstructure, Defect Formations and Mechanical Properties of Al-Si-Mg Alloys,” Mater. Sci. Appl., vol. 04, no. 03, pp. 171–178, 2013, doi: 10.4236/msa.2013.43020.

Downloads

Published

2026-11-20

How to Cite

Daffa Akhdaan, G. M. M., Maulana Saputra, E. W., & Aziz, M. N. A. (2026). EXPERIMENTAL STUDY ON MOLD HEATING TEMPERATURE AND TIME VARIATIONS IN LOST WAX CASTING OF PROPELLER FOR UNMANNED SURFACE VEHICLE. Otopro, 22(1), 1–8. https://doi.org/10.26740/otopro.v22n1.p1-8

Issue

Section

Articles
Abstract views: 0 , PDF Downloads: 0

Similar Articles

1 2 > >> 

You may also start an advanced similarity search for this article.