MICROSTRUCTURAL AND MECHANICAL RESPONSE OF LOW-CARBON ST 37 STEEL TO A 1 HOUR NITRIDING TREATMENT AT 500 °C
DOI:
https://doi.org/10.26740/otopro.v22n1.p17-24Keywords:
low-carbon ST 37 steel, nitriding, mechanical propertiesAbstract
Low carbon steel is widely used in engineering applications because of its favorable formability, machinability, and fabrication characteristics; however, its surface properties may limit performance under friction and wear conditions. This study investigated the microstructural and mechanical response of low carbon ST 37 steel subjected to a nitriding treatment at 500 °C for 1 h. Untreated material was used as the reference condition. The chemical composition was characterized using a spectrometer, while microstructural observation, Micro Vickers hardness testing, and Ogoshi wear testing were performed to evaluate changes after treatment. The material contained 0.2080% C and 98.81% Fe, confirming its classification as low carbon steel. The untreated microstructure was dominated by ferrite and pearlite. After the 1 hour treatment, ferrite and pearlite remained observable, accompanied by morphological changes at the specimen edge and fine features described as Widmanstätten like structures. The observed surface layer thickness was approximately 0.200 µm. The average hardness increased from 359.03 kg/mm² for the raw material to 414.57 kg/mm² after treatment. The average specific wear value increased from 2,9×10⁻⁷ mm²/kg to 4,0×10⁻⁷ mm²/kg. Therefore, under the experimental conditions employed, the treatment at 500 °C for 1 hour produced observable microstructural changes but did not improve the measured average hardness or wear resistance. These results indicate that the selected treatment condition requires further optimization to obtain a more favorable surface response in low-carbon ST 37 steel.
References
L. Qian, L. Zhan, B. Zhou, X. Zhang, S. Liu, and Z. Lv, “Effects of electroplastic rolling on mechanical properties and microstructure of low-carbon martensitic steel,” Materials Science and Engineering: A, vol. 812, p. 141144, Apr. 2021, doi: 10.1016/j.msea.2021.141144.
A. Karim, I. Azmy, and S. Q. Khoiriah. “Microstructure and Mechanical Properties of Pack Carburized AISI 1020 Steel Using Na2CO3 and CaCO3 Catalysts.” ResearchGate Vol. 05 No.02 2022 P-ISSN: 2714-621X DOI: 10.25299/rem.2 (May 2026): 52–59. https://doi.org/10.25299/rem.2022.vol 5. no.02.9965.
B. Cheng, H. Lu, X. Dai, S. Sun, and Z. Wang, “Effect of Treatment with Microarc Oxidation Technology on Tribological Properties of Nonvalve Metal Low-Carbon Steel,” Langmuir, vol. 40, no. 26, pp. 13375–13385, Jun. 2024, doi: 10.1021/acs.langmuir.4c00489.
A. A. Maich, R. Gronsky, and K. Komvopoulos, “Microstructure Evolution and Fretting Wear Mechanisms of Steels Undergoing Oscillatory Sliding Contact in Dry Atmosphere,” Materials, vol. 17, no. 8, p. 1737, Jan. 2024, doi: 10.3390/ma17081737.
M. R. S. Anhar and M. Kazeminezhad, “Effect of CGP on sliding wear resistance of low-carbon steel sheet,” Heliyon, vol. 11, no. 13, p. e43747, Aug. 2025, doi: 10.1016/j.heliyon.2025.e43747.
J. Miyamoto and M. Yoshida, “Surface Modification of AISI H13 Tool Steel via Atmospheric-pressure Plasma Nitriding and Superheated Steam Treatment,” ISIJ Int., vol. 64, no. 1, pp. 134–141, Jan. 2024, doi: 10.2355/isijinternational.ISIJINT-2023-418.
Drouet, Michel, and Eric Le Bourhis. “Low Temperature Nitriding of Metal Alloys for Surface Mechanical Performance.” Materials 16, no. 13 (2023): 4704. https://doi.org/10.3390/ma16134704.
R. S. Varanasi et al., “Understanding crack growth within the γ′ Fe4N layer in a nitrided low carbon steel during monotonic and cyclic tensile testing,” J Mater Sci, vol. 59, no. 31, pp. 14639–14652, Aug. 2024, doi: 10.1007/s10853-024-10014-x.
T. Bergelt, P. Landgraf, T. Grund, G. Bräuer, and T. Lampke, “Modelling of layer development and nitrogen distribution on different microstructures during plasma nitriding,” Surface and Coatings Technology, vol. 447, p. 128813, Oct. 2022, doi: 10.1016/j.surfcoat.2022.128813.
Landgraf et al., Pierre. “Evolution of Microstructure and Hardness of the Nitrided Zone during Plasma Nitriding of High-Alloy Tool Steel.” MDPI, May 19, 2022. https://doi.org/10.3390/met12050866.
Stefanie, Hoja. “An Investigation into the Wear Behavior of Martensitically Transformed Nitrided Layers.” MDPI, December 15, 2021. https://doi.org/10.3390/lubricants11110481.
Steinbacher, Steinbacher. “Optimization of Pre-Heat Treatment for Nitriding.” MDPI, December 15, 2021. https://doi.org/10.3390/ma14247766.
Dominika Panfil, Pryka. “Tribological Behavior of Gas-Nitrided 42CrMo4 Steel at Elevated Temperatures.” MDPI, December 28, 2024. https://doi.org/10.3390/coatings15010018.
M. Sommer et al., “Optimized Compound Layer Design for Highly Loaded Nitrided Gears,” J. of Materi Eng and Perform, vol. 33, no. 23, pp. 13293–13310, Dec. 2024, doi: 10.1007/s11665-024-09659-1.
E. T. Fisha, “Improving surface hardness of AISI 1045 steels using melamine derived from urea,” Heat Treatment and Surface Engineering, vol. 6, no. 1, p. 2301248, Jan. 2024, doi: 10.1080/25787616.2023.2301248.
V. T. Bonow, D. S. Maciel, N. L. Fenner, A. Reguly, A. Zimmer, and C. G. Zimmer, “Nitriding in non-toxic salts bath: An approach to implement cleaner production in the metallurgic industry,” Cleaner Engineering and Technology, vol. 4, p. 100169, Oct. 2021, doi: 10.1016/j.clet.2021.100169.
V. Ravi Raj, B. VijayaramnathB, N. Ramanan, and A. Ponshanmugakumar, “Mechanical and corrosion resistant properties of nitrided low carbon steel,” Materials Today: Proceedings, vol. 46, pp. 3288–3291, Jan. 2021, doi: 10.1016/j.matpr.2020.11.460.
K. Berladir, T. Hovorun, F. Botko, S. Radchenko, and O. Oleshko, “Thin Modified Nitrided Layers of High-Speed Steels,” Materials (Basel), vol. 18, no. 11, p. 2434, May 2025, doi: 10.3390/ma18112434.
S. A Suhymat, F. M. Al-Saraireh. “Effect Of Gas Nitriding Parameters On The Micro-Hardness Of Hihg-Speed Steel-Cutting Tools.” September 14, 2024. https://doi.org/10.5937/jaes0-50375.
İ. A. Karamanli, M. S. Gök, Y. Küçük, and O. Ünal, “Study of the Wear Resistance Plasma Nitrided GGG60 by Optimization of Surface Treatment Conditions Using Response Surface Methodology,” Inter Metalcast, vol. 19, no. 1, pp. 387–403, Jan. 2025, doi: 10.1007/s40962-024-01310-y.
Jialong, Zuo. “Study on Vacuum Gas Nitriding Process and Surface Properties of AISI 430 Stainless Steel | Surface Science and Technology | Springer Nature Link.” Springer, February 20, 2026. https://doi.org/10.1007/s44251-025-00111-7.
Reddy, C. Anil Kumar, Pothamsetty Kasi V. Rao, Begori Venkatesh, and Boggarapu Nageswara Rao. “Influence of Plasma Nitriding on Surface Layer of M50NiL Steel for Bearing Applications.” Journal of the Mechanical Behavior of Materials 33, no. 1 (2024): 20240022. https://doi.org/10.1515/jmbm-2024-0022.
T. Trisbenheiser, “Pengaruh Variasi Suhu dan Waktu Pada Proses Nitridasi Terhadap Perubahan Sifat Mekanis Baja St 40,” Jurnal Teknik Mesin Sinergi, vol. 20, no. 1, pp. 103–109, Apr. 2022, doi: 10.31963/sinergi.v20i1.3474.
A. V. Tyunkov, A. A. Andronov, E. M. Oks, M. G. Ostapenko, Yu. G. Yushkov, and D. B. Zolotukhin, “Electron-beam nitriding of carbon steel alloy in the forevacuum pressure range,” Vacuum, vol. 219, p. 112739, Jan. 2024, doi: 10.1016/j.vacuum.2023.112739.
Downloads
Published
How to Cite
Issue
Section
License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Abstract views: 0
,
PDF Downloads: 0


3.png)









