ANALISIS TEGANGAN STATIK DAN DEFORMASI FRAME ELECTRIC GANESHA SCOOTER PORTABLE (E-GASPOL) MENGGUNAKAN SOFTWARE SOLIDWORKS

Authors

  • I Gede Wiratmaja Universitas Pendidikan Ganesha
  • Nyoman Arya Wigraha Universitas Pendidikan Ganesha
  • Komang Purnayasa Universitas Pendidikan Ganesha

DOI:

https://doi.org/10.26740/otopro.v19n1.p8-17

Keywords:

Frame, Finite Element Method, Static Stress, Displacement/Deformation

Abstract

This study aims to determine and reduce static stress and increase the safety factor on the E-GASPOL vehicle frame. The type of development research used is the R2D2 type (Reflective, Recursive, Design and Development) which has three phases, namely defining, design and development and dissemination. The data analysis technique used is the finite element method, this method can solve static, dynamic, linear and non-linear problems. In this study, the static stress analysis of vehicle frame was carried out in conditions without rider load (the mass of the frame itself is 13.34 kg) and conditions with rider load (frame mass of 13.34 kg + average rider mass of 70 kg, so the total is 83.34 kg). The static stress analysis results on the four designs, the results of the modified vehicle frame design 3 have the best value, namely obtaining a maximum stress value of 1,255xN/m conditions without rider load, this result gets a decrease of 58.55% from the standard design and with a rider load of 7,699xN/m, this result gets a decrease of 58.56% from the standard design, the smaller the stress value obtained on a frame. The maximum displacement/deformation value of 1,453xmm conditions without rider load, this result gets a decrease of 77.718% from the standard design and with a rider load of 8,791xmm, this result gets a decrease of 78.10% from the standard design. From the data it can be concluded that the modified frame is better and stronger than the standard frame.

References

B. S. Putra, A. Rusdinar, and E. Kurniawan, “Desain Dan Implementasi Sistem Monitoring Dan Manajemen Baterai Mobil Listrik,” e-Proceeding Eng. Univ. Telkom, vol. 2, no. 2, pp. 1909–1916, 2015.

M. Adriana, A. A. B.P, and M. Masrianor, “Rancang Bangun Rangka (Chasis) Mobil Listrik Roda Tiga Kapasitas Satu Orang,” J. Elem., vol. 4, no. 2, p. 129, 2017, doi: 10.34128/je.v4i2.64.

M. A. Hendrawan, P. I. Purboputro, M. A. Saputro, and W. Setiyadi, “Perancangan Chassis Mobil Listrik Prototype ‘ Ababil ’ dan Simulasi Pembebanan Statik dengan Menggunakan Solidworks Premium 2016,” 7th Univ. Res. Colloq. 2018, pp. 96–105, 2018.

A. Setiawan, F. Rizayana, and B. Ariantara, “Perancangan Frame Mobil Formula Student Electric Vehicle,” Universitas Pasundan, 2019.

K. Firdaus, K. R. Dantes, and I. N. P. Nugraha, “Analisis Perbandingan Tegangan Statik Material Galvanized Steel Dengan Material Aluminium Alloys 7076-T6 (Sn) Pada Frame Ganesha Scooter Underwater (GSU) Menggunakan Software Solidworks,” J. Pendidik. Tek. Mesin Undiksha, vol. 8, no. 1, pp. 20–27, 2020, doi: 10.23887/jptm.v8i1.27302.

K. Budarma, K. R. Dantes, and G. Widayana, “Analisis Komparatif Tegangan Statik Pada Frame Ganesha Electric Vehicles 1.0 Generasi 1 Berbasis Continous Variable Transmission (Cvt) Berbantuan Software Ansys 14.5,” J. Pendidik. Tek. Mesin Undiksha, vol. 4, no. 1, 2020, doi: 10.23887/jjtm.v4i1.8043.

M. Taufiq, “ANALISIS KEKUATAN RANGKA MESIN HAMMER MILL LIMBAH KACA MENGGUNAKAN SOLIDWORKS 2021,” 2021.

R. S. Harahap, “Analisis Kekuatan Puntir Baja Karbon Rendah Dengan Metode Elemen Hingga Menggunakan Software (Solidworks),” Universitas Muhammadiyah Sumatra Utara, 2020.

J. A. Saz, F. Alibas, A. Yani, and Nurhayati, “Pengembangan Media Presentasi Interaktif Semi Laboratorium Virtual pada Pokok Bahasan Listrik Dinamis,” Saintifik, vol. 1, no. 1, pp. 26–33, 2015, doi: 10.31605/saintifik.v1i1.68.

S. Wunda, A. Z. Johannes, R. K. Pingak, and A. S. Ahab, “Analisis Tegangan , Regangan Dan Deformasi Crane Hook Dari Material Baja Aisi 1045 Dan Baja St 37 Menggunakan Software Elmer,” J. Fis. Fis. Sains dan Apl., vol. 4, no. 2, pp. 131–137, 2019.

Downloads

Published

2023-11-28

Issue

Vol 19 No 1 Nov 2023

Section

Article

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Authors who publish with this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a  Creative Commons: Attribution-NonCommercial 4.0 International (CC BY-NC) that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
    2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Abstract views: 75 , PDF Downloads: 166