THE EFFECT OF VARIATIONS IN CURRENT AND WELDING SPEED OF SMAW ON THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF LOW CARBON STEEL

Authors

  • Yudi Siswanto
  • Angga Tegar Setiawan
  • Amiruddin Amiruddin
  • Ika Nurjannah Universitas Negeri Surabaya

DOI:

https://doi.org/10.26740/otopro.v22n1.p9-16

Keywords:

SMAW, low-carbon steel, welding current, travel speed, heat input, tensile strength, HAZ hardness, grain size

Abstract

. Shielded Metal Arc Welding (SMAW) is widely applied in industrial fabrication due to its versatility and cost efficiency; however, inappropriate selection of welding parameters can lead to inconsistent joint quality. This study investigates the effects of welding current and speed on the mechanical properties and microstructure of low-carbon steel (SS400) welded using SMAW. A 3² factorial design was employed with three current levels (70, 80, and 90 A) and three welding speeds (2, 3, and 4 mm/s), producing 27 specimens. Mechanical characterisation included tensile testing (UTS) and Vickers hardness measurements in the heat-affected zone (HAZ), while microstructures were examined using optical microscopy after nital etching. Heat input was calculated as the primary thermal parameter. Results show that lower heat input, achieved through reduced current and higher welding speed, produced higher UTS (up to 439 MPa) and HAZ hardness (up to 187 HV), associated with finer ferrite–pearlite grains of 12–15 µm. Conversely, high heat input (84.38 kJ/mm) caused grain coarsening (18–22 µm), reducing UTS to 386 MPa and hardness to 158 HV. Two-way ANOVA confirmed significant effects of current and speed on UTS and HAZ hardness (p < 0.001), with welding speed as the dominant factor (F = 39.15 for UTS; F = 67.99 for HAZ hardness). Multiple linear regression yielded R² = 0.81 for UTS prediction. These findings provide a quantitative basis for optimising SMAW parameters for improved mechanical performance of low-carbon steel structural joints.

Keywords: SMAW; welding current; welding speed; heat input; low carbon steel; mechanical properties; microstructure

References

R. Conte, F. R. Battista, G. Ambrogio, Submerged arc welding process: enhancement of production performance based on metallurgical observations. Int. J. Adv. Manuf. Technol. 134, 781–793 (2024). https://doi.org/10.1007/s00170-024-14153-y

P.K. Baghel, Effect of SMAW process parameters on similar and dissimilar metal welds: An overview. Heliyon 8(12), e12161 (2022). https://doi.org/10.1016/j.heliyon.2022.e12161

J. Singh, G. Singh, Effects of variation in welding current during SMAW process on A36 mild steel. Int. J. Res. Appl. Sci. Eng. Technol. 10(8), 259–264 (2022). https://doi.org/10.22214/ijraset.2022.46148

M.S. Afzal, A. Wakeel, M.A. Nasir, M.I. Qazi, M. Abas, Optimization of process parameters for SMAW of ASTM A572 grade 50. J. Eng. Res. (2024). https://doi.org/10.1016/j.jer.2024.01.005

T. Tarmizi, Y. B. Nugraha, I. Irfan, Analysis of current on mechanical properties and microstructure of A53 Gr B material with gas tungsten arc welding process. TEKNIK 42(1), 20–28 (2021). https://doi.org/10.14710/teknik.v42i1.33209

H. Wibowo, M. N. Ilman, P. T. Iswanto, Analisa heat input pengelasan terhadap distorsi, struktur mikro dan kekuatan mekanis baja A36. Jurnal Rekayasa Mesin 7(1), 5–12 (2016). https://doi.org/10.21776/ub.jrm.2016.007.01.2

A. Royani, Pengaruh suhu terhadap laju korosi baja karbon rendah dalam media air laut. Jurnal Simetrik 10(2), 344–349 (2020; published online 2021). https://doi.org/10.31959/js.v10i2.493

R. Celin, J. Burja, Effect of cooling rates on the weld heat affected zone coarse grain microstructure. Metall. Mater. Eng. 24(1), 37–44 (2018). https://doi.org/10.30544/342

Azwinur, Syukran, Hamdani, Kaji sifat mekanik sambungan las butt weld dan double lap joint pada material baja karbon rendah. SINTEK 12(1), 9–16 (2018). https://doi.org/10.24853/sintek.12.1.9-16

H. Helanianto, E. Epriyandi, H. Rahmadi, Pengaruh variasi arus pengelasan SMAW terhadap kekerasan logam induk dan logam las. ELEMEN 7(2), 138–147 (2020). https://doi.org/10.34128/je.v7i2.148

D. Ary, N. Muhayat, T. Triyono, Research gap finding in shielded metal arc welding of steel. E3S Web Conf. 465, 01012 (2023). https://doi.org/10.1051/e3sconf/202346501012

C. Johan, M. Pineng, M. Pakiding, Analisis kekuatan bending hasil pengelasan SMAW pada baja ST 42 menggunakan pendingin oli SAE 20W-50 dengan memvariasi kuat arus. J. Teknik Industri 9(2), 390 (2023). https://doi.org/10.24014/jti.v9i1.22989

M. A. Shomad, M. Shahar Mushfi, Analisis pengaruh variasi elektroda las E6013 dan E7018 terhadap kekuatan tarik dan kekerasan pada bahan baja SS 400. Dinamika Teknik Mesin 7(2), 73–79 (2017). https://doi.org/10.29303/d.v7i2.156

S. Dharma, S. Suherman, S. Sarjianto, R. Sebayang, H. B. Kurniyanto, Pengaruh kuat arus terhadap sifat mekanis pada aluminium Al-Si-Fe dengan filler ER 4043 metode pengelasan GTAW. Jurnal Rekayasa Mesin 17(1), 103–112 (2022). https://doi.org/10.32497/jrm.v17i1.3068

A. Widyianto, A. Yudianto, H. Sofyan, G. Gunadi, Karakterisasi kualitas lasan pada bahan serupa AZ31B dengan proses micro-friction stir spot welding (µFSSW) untuk aplikasi kendaraan. J. Pendidikan Vokasi Otomotif 5(2), 101–118 (2023). https://doi.org/10.21831/jpvo.v5i2.60132

A. S. Nurrohkayati, D. Zulrahman, S. Syach, M. Khairul, Welding quality engineering using the design of experiment method (Taguchi’s method). Procedia Eng. Life Sci. 1(1) (2021). https://doi.org/10.21070/pels.v1i1.882

P. Kusdiyarto, R. D. Djatmiko, Analisis variasi included angle terhadap distorsi pada sambungan las SMAW. J. Dinamika Vokasional Teknik Mesin 3(1), 12–18 (2018). https://doi.org/10.21831/dinamika.v3i1.19112

V. K. Kumawat, Performance analysis of welded joint made by MIG welding process on EN-24 steel work pieces for micro hardness. Int. J. Res. Appl. Sci. Eng. Technol. 7(5), 763–770 (2019). https://doi.org/10.22214/ijraset.2019.5128

M. D. Jagtap, A review on optimization of welding process using different statistical techniques. Int. J. Res. Appl. Sci. Eng. Technol. 6(4), 2097–2100 (2018). https://doi.org/10.22214/ijraset.2018.4359

S. Park, M. Choi, D. Kim, C. Kim, N. Kang, Modeling yield strength of austenitic stainless steel welds using multiple regression analysis and machine learning. Metals 13(9), 1625 (2023). https://doi.org/10.3390/met13091625

S. Nugraha, H. Oktadinata, Pengaruh metode pengelasan TIG dan SMAW terhadap sifat mekanik baja karbon SS400. J. Ilmiah Teknik Mesin 10(1), 37 (2022). https://doi.org/10.33558/jitm.v10i1.2947

C. Umam, U. Sukamto, Pengaruh variasi kuat arus pengelasan terhadap berat deposit las per milimeter. J. Metallurgical Eng. Process. Technol. 3(2), 159 (2023). https://doi.org/10.31315/jmept.v3i2.6584

M.A. Shaleh, W. Wijoyo, R. Rohmadi, Pengaruh variasi metal transfer terhadap karakteristik sambungan las GMAW. J. Metallurgical Eng. Process. Technol. 3(2), 139 (2023). https://doi.org/10.31315/jmept.v3i2.8764

S. Muddin, Ariyanto, Sriwati, M. F. Rahman, Optimization of welding direction model parameters to enhance the tensile strength of ST 42 steel joints through variation of current strength simulation. Eastern-European J. Enterprise Technol. 2(12[128]), 23–31 (2024). https://doi.org/10.15587/1729-4061.2024.295536

A. Jefiza, D. Diono, S. Lukito, Analisis data monitoring proses pengelasan FCAW berbasis multilayer perceptron. J. Integrasi 14(2), 153–158 (2022). https://doi.org/10.30871/ji.v14i2.4538

British Standards Institution, BS EN 1011-1:2009: Welding. Recommendations for welding of metallic materials. General guidance for arc welding (2009). https://doi.org/10.3403/30158904

International Organization for Standardization, ISO 18491:2026, Welding and allied processes—Measurement of arc energies (2026). https://www.iso.org/standard/88807.html

ASTM International, ASTM E112-24, Standard test methods for determining average grain size (2024). https://store.astm.org/e0112-24.html

Downloads

Published

2026-11-20

How to Cite

Siswanto, Y., Setiawan, A. T., Amiruddin, A., & Nurjannah, I. (2026). THE EFFECT OF VARIATIONS IN CURRENT AND WELDING SPEED OF SMAW ON THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF LOW CARBON STEEL. Otopro, 22(1), 9–16. https://doi.org/10.26740/otopro.v22n1.p9-16

Issue

Section

Articles
Abstract views: 0 , PDF Downloads: 0