STUDI VARIASI JENIS MATERIAL TALI PADA MODIFIKASI ALAT PENGUKURAN TORSI POMPA SENTRIFUGAL

Authors

  • Taufik Afandi Universitas Muhammadiyah Sidoarjo
  • Edi Widodo Universitas Muhammadiyah Sidoarjo
  • Prantasi Harmi Tjahjanti Universitas Muhammadiyah Sidoarjo
  • Iswanto Iswanto Universitas Muhammadiyah Sidoarjo

DOI:

https://doi.org/10.26740/otopro.v16n2.p50-57

Keywords:

centrifugal pump torque test, modification of measuring instruments

Abstract

The focus of this research is to analyze variations in the type of rope material and size as a link for measuring the force on a centrifugal pump, namely to find out the type of material and the size of the rope that is suitable to minimize the loss of force contained in the wire. To find out the type of calculation and comparison of the values for various types of material. From the tensile test that has been done, the highest UTS (Ultimate Tensille Stress) value was obtained in a polypropylene monofilament rope specimen with a stress value of 602.17 kgf with 382.14% elongation. The highest stress calculation value data was obtained by the Polypropylene monofilament rope specimen with a value of 738,85 at elongation to 360%. The highest modulus of elasticity obtained by Nylon rope was 4,564  . This shows that the modulus of elasticity is inversely proportional to the stress value, which was the stress value of nylon straps that was the highest compared to other specimens but had the highest elastic modulus value among other specimens.

Author Biographies

Taufik Afandi, Universitas Muhammadiyah Sidoarjo

Mechanical Engineering Department

Edi Widodo, Universitas Muhammadiyah Sidoarjo

Mechanical Engineering Department

Prantasi Harmi Tjahjanti, Universitas Muhammadiyah Sidoarjo

Mechanical Engineering Department

Iswanto Iswanto, Universitas Muhammadiyah Sidoarjo

Mechanical Engineering Department

References

A. F. Silaen, œAnalisa Karakteristik Pompa Sentritugal Rangakaian Single, Serie Dan Paralel. Telematik, J. rekayasa pangan dan Pertan., vol. 2, no. 2, 2011.

R. Y. Pradhana and E. Widodo, œAnalisa Pengaruh Variasi Diameter Pipa Tekan Pvc Pada Pompa Aksial Untuk Kecepatan Gaya Dorong Air, R E.M. (Rekayasa Energi Manufaktur) J., vol. 2, no. 1, pp. 3743, 2017.

Edi Widodo; Gagah Deffi Priyambudi, œREKAYASA SLIDING SEAT PADA POMPA OBSERVASI UNTUK EFEKTIFITAS LABORATORIUM, TURBO J. Tek. Mesin Univ. Muhammadiyah Metro, vol. 7, no. 1, pp. 6573, 2018.

E. W. R. Y. Pradana, œAnalysis of pipe diameter variation in axial pumps for reducing head loss, in 2017 1 st International Conference on Engineering and Applied Technology (ICEAT), 2018, pp. 18.

I. N. Gusniar, œOPTIMALISASI SISTEM PERAWATAN POMPA SENTRIFUGAL DI UNIT UTILITY PT.ABC, J. Ilm. SOLUSI, vol. 1, no. 1, 2014.

F. Ansori and E. Widodo, œAnalysis on Centrifugal Pump Performance in Single , Serial , and Parallel, JEMMME (Journal Energy, Mech. Mater. Manuf. Eng., vol. 3, no. 2, pp. 7986, 2018.

G. Suwoto, œKaji Eksperimental Kinerja Turbin Air Hasil Modifikasi Pompa Sentrifugal untuk Pembangkit Listrik Tenaga Mikrohidro, in SNST ke-3 Tahun 2012, 2004, pp. 6064.

S. Abouda, F. Nollet, A. Chaari, N. Essounbouli, and Y. Koubaa, œDirect Torque Control - DTC of Induction Motor Used for Piloting a Centrifugal Pump Supplied by a Photovoltaic Generator, Int. J. Electr. Comput. Energ. Electron. Commun. Eng., vol. 7, no. No¯: 8, pp. 11101115, 2013.

U. Klinge K. Junge M. Stumpf A. P. Öttinger B. Klosterhalfen, œFunctional and morphological evaluation of a lowweight, monofilament polypropylene mesh for hernia repair, J. Biomed. Mater. Res., vol. 63, no. 2, 2002.

Novrizal, œVISIBILITAS TALI MULTIFILAMEN UNTUK BAHAN ALAT PENANGKAPAN IKAN PADA KEDALAMAN PERAIRAN YANG BERBEDA, Berk. Perikan. Terubuk, vol. 42, no. 1, 2014.

and C. C. C. Charles Scott, Dan Wu, Chia-Chi Ho, œLiquid-Core Capsules via Interfacial Polymerization: A Free-Radical Analogy of the Nylon Rope Trick, J. Am. Chem. Soc., vol. 127, no. 12, 2005.

E. H. Purwono and B. Yatnawijaya, œKekuatan Bahan Tali Tampar, Rev. Urban. Archit. Stud., vol. 11, no. 1, pp. 102112, 2013.

Downloads

Published

2021-05-27

Issue

Section

Article
Abstract views: 256 , PDF Downloads: 615