LEVELLING MESIN BUBUT LZ 330 G MENGGUNAKAN ALAT UKUR SPIRIT LEVEL

Authors

  • Roberth Marshall Ratlalan Akademi Komunitas Industri Manufaktur Bantaeng
  • Nurisma Maharani Akademi Komunitas Industri Manufaktur Bantaeng

DOI:

https://doi.org/10.26740/otopro.v18n2.p71-76

Keywords:

Leveling, Lathe, Slope Value

Abstract

The leveling process is the initial stage before operating a lathe. The test will be carried out if the flatness on the machine and the results have deviated greatly, it must be leveled on the lathe. This study aims at a high level of accuracy of machine tools in the form of leveling on three types of Gedee Weiler LZ 330 G lathes located at the AK-Manufaktur Bantaeng Manufacturing Workshop. This type of research is categorized as quantitative research which is an inductive, objective and scientific method in which the data is processed in the form of numbers or statements which are then analyzed. Data from the test results of the M1 lathe with the longitudinal tilt direction towards the off head, while in the transverse position the slope direction is towards the rear slide. Flatness deviation reaches 1.06 mm in the longitudinal position and 0.15 mm in the transverse position. For the M2 lathe, the direction of the longitudinal slope is the direction of the off head, while in the transverse position, the direction of the slope of the fore runway. Deviation of flatness reaches 1.3 mm in the longitudinal position and 1.75 in the transverse position and the M3 lathe with the longitudinal slope direction towards the off head, while in the transverse position the slope direction is towards the front of the runway. Flatness deviation reaches 1.65 mm in the longitudinal position and 10.15 mm in the transverse position.

References

Akhmad, M. M. (2015). Analisis Metoda Pengukuran Penyimpangan Geometrik Menggunakan Universal Bridge, Carriage Dan Spirit Level Pada Bedways Mesin Bubut. p. 18.

Buku Original Instruction Manual Precizion Center Lathe Gedee Weiler LZ 330 G.2016.Bantaeng:Gedee Weiler

Buku Panduan Laporan Akhir AK-Manufaktur Bantaeng. 2020. Bantaeng: AK-Manufaktur Bantaeng

Gugun gundara, s. R. (2017). Pengukuran Ketelitian Komponen Mesin Bubut Dengan Standar ISO 1708. Al Jazari Journal of Mechanical Engineering, 8-15.

Hadi, I. (2014). Analisa Kedataran Guide Ways Terhadap Pengaruh Gerak Carriage Pada Mesin Bubut Celtic 14 Dengan Alat Ukur Digital Pastm Di Smk Negeri 2 Bengkulu. p. 8.

Mangngi, f. (2018). Evaluasi Kondisi Mesin Bubut Harizon T300 Menurut Metode Schlesinger Sebagai Acuan Dalam Melakukan Tindakan Perawatan . Sintek: Jurnal Mesin Teknologi, 87-99.

Situmorang, R. (2015). Relevansi Ketelitian Geometrik Mesin Perkakas Terhadap Akurasi Hasil Kerja (Produk). pp. 1-3.

Wajudi, s. (2015). Perataan (Levelling) Dan Penjajaran (Alignment). p. 34. https://adoc.pub/bab-ii-perataan-levelling-dan-penjajaran-alignment.html. Diakses pada pukul 16:00, 11 Oktober 2020

Downloads

Published

2023-05-25

Issue

Vol 18 No 2 Mei 2023

Section

Article

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Authors who publish with this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a  Creative Commons: Attribution-NonCommercial 4.0 International (CC BY-NC) that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
    2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Abstract views: 276 , PDF Downloads: 520